Features
- Electronic Module (IP65) – mode selectable for static and drawDown levels, removable for easy cleaning and servicing
- Probe (IP68) – fully pressure/depth rated, 5/8” field replaceable for optional casing or bottom detector probes
- Steel Tape – high tensile steel, jacketed with polyethylene, high break strength, stretch resistant and lifelong legibility – markings in engineering scale (1/100’) or metric (mm)
- Padded Carry Case – to protect your precision water level meter from the elements
- Tape Guide and Hanger – to support the meter at the well head and to protect the tape from sharp edges on the well casing
- Vinyl Holding Grip – molded to the frame, ergonomic easy grip
- Winding Handle – custom made for easy rewinding with gloved hands
- Carrying bag and tape guide included
| Reel Weight | 2.4Kg |
| Height | 356mm (14”) |
| Width | 279mm (11”) |
| Depth | 241mm ( 9.5”) |
| Probe Weight | 158g |
| Length | 213mm (8.4”) |
| Diameter | 16mm (0.625”) |
| Depth Rating | Full Length of Tape |
| Wetted Materials | Stainless Steel, Viton, Delrin and Teflon |
| Power Source | 9 Volt Alkaline |
| Operating Mode | Static/drawDown |
| Sensitivity Control | Stainless Steel and Aluminum Construction |
| Audio/Visual Indication | Ultra Bright Red LED and 80dbi Buzzer |
| Tape Jacketing | Polyethylene |
| Tape Conductors | 7 strand (4 Stainless Steel and 3 Copper) |
| Tape Markings | Engineering Scale or Metric – Under Jacketing |
| Limited Warranty | 5 Years (Probe 1 Year) |
Ordering Information:
Tape Lengths:
PN# 1124 – 15m
PN# 1125 – 30m
PN# 1126 – 45m
PN# 1127 – 60m
PN# 1128 – 100m
PN# 1130 – 150m
PN# 1131 – 180m
PN# 1132 – 200m
PN# 1133 – 300m
PN# 1134 – 450m
PN# 1135 – 600m
Probe Options:
Well Casing Indicator Probe – PN# 1503
The Well Casing Indicator Probe is used to measure the depth of metal casing in wells and boreholes from two inches in diameter and upward. The Well Casing Indicator Probe works using magnetism. While the probe sits within the magnetic field of the steel casing, an auditory and visual signal is active. When the probe leaves the magnetic field the signal stops. The well casing measurements are taken directly from the tape.
Well Depth Indicator Probe – PN# 1502
The Well Depth Indicator Probe (or bottom detector) is used to measure full depth in wells and boreholes. The Well Depth Indicator Probe uses a pressure sensitive plunger to measure the distance to the bottom of the well. When the Well Depth Indicator Probe reaches the bottom of the well, the plunger enters the probe body closing a switch, initiating an audible and visual signal at the top of the well. The well depth reading is taken directly from the tape.
3/8” Probe Option – PN# 1504
3/8” Replacement Probe – PN# 1415
The dipper-T with the 3/8” probe option is used for measuring water levels in narrow tubes and piezometers. The 3/8” probe is not removable and must be ordered at time of manufacturing. The probe is pressure rated up to 300ft for 20 minutes.
Power Reel – PN# 1500
CE Certified – Emissions & Immunity for Measurement, Control, and Laboratory Use Electrical Equipment
IEC 61326-1:2012 / EN 61326-1:2013
The Power Reel is intended for longer tape lengths. The Power Reel can hold tape lengths from 2000’/600m up to 3500’/1100m. The power source is 12 V DC that can be taken from the regular 12 V DC system on most vehicles. The Power Reel makes easy work of lowering and raising the longer tape lengths into and out of the well. A hand crank is included in case of power failure.
heron-dippert-datasheet-2016